---
title: "Edge Fiber Laser: Engraving Is the Wrong Size, Distorted, or Mirrored"
description: Fix an Edge fiber laser that engraves the wrong size, bows or stretches near the edges, or marks backwards — check the lens profile, Device Settings, 9-point correction and scale.
---

[Skip to content](https://support.salasers.com/edge-fiber-laser-engraving-wrong-size-distorted-mirrored#main-content)

English

Show submenu for translations

[Submit a Ticket](https://support.salasers.com/kb-tickets/new?hsLang=en)

![MicrosoftTeams-image.png\]](https://support.salasers.com/hs-fs/hubfs/Logos/MicrosoftTeams-image.png?height=50&name=MicrosoftTeams-image.png)

Open main navigation

Close main navigation

- English
  
  Show submenu for translations
- [Submit a Ticket](https://support.salasers.com/kb-tickets/new)
- Go to salasers.com

 Go to salasers.com

 Hello. How can we help you?

- There are no suggestions because the search field is empty.

1. [SA Laser Knowledge Base](https://support.salasers.com/?hsLang=en)
2. [Fiber (Galvo) Lasers](https://support.salasers.com/fiber-galvo-lasers?hsLang=en)

# Edge Fiber Laser: Engraving Is the Wrong Size, Distorted, or Mirrored

## Fix an Edge fiber laser that engraves the wrong size, bows or stretches near the edges, or marks backwards — check the lens profile, Device Settings, 9-point correction and scale.

If your Edge fiber laser marks a 1" square that doesn't measure 1", artwork bows or stretches toward the edges, or a design comes out backwards, the cause is almost always a setting or calibration, not the machine itself. It shows up most often after a new computer, a LightBurn update, a lens swap, or a rotary job. Work through the steps below in order.

### Before you start

- Run a **simple test file** (a plain square), not customer artwork.
- Have **calipers** and a high-contrast test material handy. Black construction paper works well on a fiber laser.
- Ask yourself: **what changed?** New PC or laptop, LightBurn update, lens change, rotary use, or settings imported from another machine.

### Step 1: Check the basics in LightBurn

1. Make sure the **correct device profile** is selected for your machine and the **lens that is installed**. Each lens should have its own profile.
2. Make sure **Rotary is turned off** if you're not using the rotary. Leaving rotary enabled will change the size of flat jobs.
3. Check your **units** (mm vs. inches, mm/s vs. in/min). Since LightBurn 2.0, speed units sometimes change on their own, and the Cuts/Layers window may not match the Cut Settings Editor. Check units first if your settings suddenly "look different."
4. Make sure the **part is flat and at focus**. If one side of a part sits higher or lower than the other (for example, two sides of a firearm frame), the engraved size will change. See [Finding Optimal Focus for Your Galvo Fiber Laser](https://support.salasers.com/finding-optimal-focus-for-your-galvo-fiber-laser?hsLang=en).

### Step 2: New computer or laptop? Check Device Settings

When LightBurn is set up on a new computer, Device Settings are the most common problem. Open **Device Settings** and check:

- **Galvo negate:** on SA Laser Edge machines, **Galvo 2 is the X axis** and **Negate is off for both galvos**. If Negate got turned on, your work will mark backwards or flipped.
- **Field size:** it must match the lens that's installed.
- **Scale:** if the scale values were reset, jobs will come out the wrong size.

The easiest fix is to re-import your **SA Laser bundle** (or your own LightBurn User Bundle from the old computer). See [How to Move LightBurn to a New Computer](https://support.salasers.com/move-lightburn-to-new-computer?hsLang=en). If you don't have your SA bundle file, contact us and we'll get it to you.

### Step 3: Wrong size or distorted? Run 9-Point Correction

9-Point Correction fixes the scale, bulge, skew and trapezoid distortion that every galvo lens has. Run it if your design looks good in the center but bad near the edges, squares look like trapezoids, or you changed lenses.

1. Set your focus, and place black construction paper on the bed.
2. Go to **Laser Tools \> Calibrate Galvo Lens \> 9 Point Correction (Easy)**.
3. Enter the lens working area and box size. For a **220mm lens**, enter **220mm** for the working area and **190mm** for the box. For other lenses, use that lens's size and keep the box at about 85-90% of the working area.
4. Enter the SPARK training starting settings: **Speed 120 mm/s, Power 20%, Frequency 20 kHz** (leave Q-Pulse as is). Click **Frame**, line up your paper, then **Start**. If any part doesn't mark clearly, run it again or adjust speed/power until it does.
5. Pick the LightBurn dragon that matches the orientation of what was marked. If you imported the SA bundle, it should match the default SA orientation.
6. Measure the X distances (1-6) where the lines cross and enter them, then the Y distances, then the two diagonals.
7. Click **Done** to apply the corrections.

Video: [9-Point Calibration LightBurn Tutorial | SA Laser](https://www.youtube.com/watch?v=Iu_jFgCSBWU)

### Step 4: Fine-tune the scale

1. Draw a **4" x 4" square** and mark it in line mode on test material.
2. Measure the X and Y sides with calipers, corner to corner.
3. Open **Device Settings**. Click the **...** button next to **Scale** for **Galvo 1 (Y axis)**. Enter **4** as the requested size and your measurement as the measured size. Click **OK**.
4. Repeat for **Galvo 2 (X axis)**.

**Note:** the units set in LightBurn must match the units you measure in.

### Step 5: Red preview doesn't match the mark?

If the size is right but the red frame doesn't line up with the burn, that's red-dot alignment, not lens correction. Follow [Red Laser Alignment in LightBurn](https://support.salasers.com/red-laser-alignment-in-lightburn?hsLang=en). Don't trust the framing until a test mark confirms it.

### Changed lenses?

A new lens needs its own profile, its own focus, and its own 9-point correction. See [Changing a Galvo Laser Lens: A Comprehensive Guide](https://support.salasers.com/changing-a-galvo-laser-lens-a-comprehensive-guide?hsLang=en). Once each lens is calibrated, you can switch profiles in LightBurn without recalibrating every time.

### Still not right?

Contact SA Laser Support at **888-964-3568** or **customerservice@salasers.com** (Mon-Fri, 9-5 CT). Please send a photo of your test square with caliper measurements and a screenshot of your Device Settings.

 

 

- [Lightburn](https://support.salasers.com/lightburn?hsLang=en#main-content)

    - [Lightburn For Galvo (Fiber)](https://support.salasers.com/lightburn?hsLang=en#lightburn-for-galvo-fiber)
    - [Lightburn For Gantry (Co2,RF)](https://support.salasers.com/lightburn?hsLang=en#lightburn-for-gantry-co2rf)
- [Fiber (Galvo) Lasers](https://support.salasers.com/fiber-galvo-lasers?hsLang=en#main-content)

    - [Troubleshooting](https://support.salasers.com/fiber-galvo-lasers?hsLang=en#troubleshooting)
- [Co2 Lasers](https://support.salasers.com/co2-lasers?hsLang=en#main-content)

    - [Razor Series](https://support.salasers.com/co2-lasers?hsLang=en#razor-series)
- [Troubleshooting](https://support.salasers.com/troubleshooting?hsLang=en)
- [EzCad 2](https://support.salasers.com/ezcad-2?hsLang=en)
- [How-To Guides](https://support.salasers.com/how-to-guides?hsLang=en)
- [Explainers](https://support.salasers.com/explainers?hsLang=en)
- [Tools & Features](https://support.salasers.com/tools-features?hsLang=en#main-content)

    - [User Interface](https://support.salasers.com/tools-features?hsLang=en#user-interface)
    - [Essential Functions](https://support.salasers.com/tools-features?hsLang=en#essential-functions)
    - [Layout and Design](https://support.salasers.com/tools-features?hsLang=en#layout-and-design)

# San Antonio Laser

SALasers.com Help Center

Copyright © 2026, San Antonio Laser