---
title: "Razor CO2: Laser Head Hits the Wall, Takes Forever to Home, or the X-Axis Won't Move"
description: Razor CO2 laser head hitting the wall or not homing? Check the air assist fitting, test the X and Y limit switches, and set the sensor bracket gap.
---

[Skip to content](https://support.salasers.com/razor-co2-laser-wont-home-hits-wall-x-axis#main-content)

English

Show submenu for translations

[Submit a Ticket](https://support.salasers.com/kb-tickets/new?hsLang=en)

![MicrosoftTeams-image.png\]](https://support.salasers.com/hs-fs/hubfs/Logos/MicrosoftTeams-image.png?height=50&name=MicrosoftTeams-image.png)

Open main navigation

Close main navigation

- English
  
  Show submenu for translations
- [Submit a Ticket](https://support.salasers.com/kb-tickets/new)
- Go to salasers.com

 Go to salasers.com

 Hello. How can we help you?

- There are no suggestions because the search field is empty.

1. [SA Laser Knowledge Base](https://support.salasers.com/?hsLang=en)
2. [Co2 Lasers](https://support.salasers.com/co2-lasers?hsLang=en)
3. [Razor Series](https://support.salasers.com/co2-lasers?hsLang=en#razor-series)

# Razor CO2: Laser Head Hits the Wall, Takes Forever to Home, or the X-Axis Won't Move

## Fix Razor startup homing problems by checking the air assist fitting, limit switches, and sensor bracket gap.

When you turn on a Razor CO2 laser, the laser head should travel to its home position in the **back right corner**, find its limit switches, and be ready within a few seconds. If the head bangs into the side wall, sits in the corner for a long time, or the X-axis won't move at all afterward, the machine usually isn't seeing one of its home sensors. The motors aren't "dead." When the controller can't find home, it gives up and the motor goes into protection mode. This guide walks you through the checks.

### Signs you have a homing problem

- The gantry or laser head bumps the back right corner or side wall, sometimes repeatedly, when the machine starts up or resets.
- The head stays in the back right corner for **more than about 5 seconds** after power-on.
- After a long wait, the axes go limp and you can push the laser head around by hand while the machine is on (you shouldn't be able to).
- After the reset finally finishes, only one axis moves, or the X-axis won't move from the keypad or LightBurn.

**Important:** Don't keep resetting the machine to "see if it's fixed." Each failed home can crash the head into the wall again. Move the head by hand with the machine **off** while you check things.

### Step 1: Check the air assist fitting

On the laser head, the air assist fitting must point toward the **back** of the machine. If it's turned toward the side, it can hit the X-axis wall before the head reaches the sensor and stop the X motor.

1. Turn the machine off.
2. Look at the air assist fitting on the laser head.
3. If it faces the side, rotate it so it faces the back of the laser.

### Step 2: Test the X and Y limit switches

1. With the machine **off**, move the laser head by hand to the center of the work bed.
2. Turn the machine on and **immediately press ESC** on the keypad. This cancels homing so you can test the sensors with the power on.
3. Find the **X-axis limit switch**, a small black sensor on the back right side of the gantry.
4. Hold a screwdriver or other piece of metal on top of the sensor. A **red LED** should light up at the bottom of the sensor.
5. Remove the top side panel on the right side of the machine and find the **Y-axis limit switch** toward the bottom right. Test it the same way with a piece of metal.
6. Turn the machine off.

If either sensor **does not** light up, stop here and contact SA Laser Support for next steps.

### Step 3: Check the gap between the sensor and the metal bracket

If both sensors light up, the most common cause is the gap between the sensor and the metal bracket (flag) that passes over it. A bracket can get bent or moved, especially after a crash, and end up too far from the sensor to be detected, or so low that it hits.

1. With the machine **off**, move the laser head by hand over to the right side so the metal bracket sits above the X sensor.
2. Look at the gap between the bracket and the sensor.
3. **Gap too large:** gently press the top bracket down so it sits closer to the sensor.
4. **Gap too small, or the bracket touches the sensor:** gently pull the bracket up.
5. Aim for **a few millimeters** of space. It should never touch the sensor, because that can cause a crash.
6. Move the head back and forth by hand to make sure the bracket passes over the sensor without hitting it.
7. Take a photo of the bracket over the sensor and send it to support so we can confirm it looks right.
8. Turn the machine on and watch it home to the back right corner.

### Step 4: Check the limit setting in LightBurn

If the machine still won't home correctly after the sensors and bracket check out, make sure **Limit Trigger** is set to **True** for both axes in LightBurn's machine settings. If you're not sure where to find this, contact support before changing anything else in Machine Settings.

### Related: the head goes home but not back to your origin after a reset

That's a setting, not a sensor problem. On Razor machines with the **844 controller card**, go to the keypad **Menu \> User Parameters \> Home Parameters \> Return after Reset** and select **Home position**.

### Still having trouble?

Contact SA Laser Support at **888-964-3568** or **customerservice@salasers.com** (Mon-Fri, 9-5 CT). Please include:

- Your machine model and serial number
- A short video of the machine turning on and homing
- A photo of the X-axis sensor and the bracket above it
- Whether the red LED lit up on each sensor in Step 2

### Related articles

- [Air Assist Setup for Razor CO2 Lasers](https://support.salasers.com/air-assist-setup-for-razor-co2-lasers?hsLang=en)
- [Configuring a Ruida Controller: A Step-by-Step Guide](https://support.salasers.com/configuring-ruida-controller?hsLang=en)
- [Finding and Connecting Your Laser in LightBurn for CO2 Lasers](https://support.salasers.com/finding-and-connecting-your-laser-in-lightburn-for-co2-lasers?hsLang=en)

 

- [Lightburn](https://support.salasers.com/lightburn?hsLang=en#main-content)

    - [Lightburn For Galvo (Fiber)](https://support.salasers.com/lightburn?hsLang=en#lightburn-for-galvo-fiber)
    - [Lightburn For Gantry (Co2,RF)](https://support.salasers.com/lightburn?hsLang=en#lightburn-for-gantry-co2rf)
- [Fiber (Galvo) Lasers](https://support.salasers.com/fiber-galvo-lasers?hsLang=en#main-content)

    - [Troubleshooting](https://support.salasers.com/fiber-galvo-lasers?hsLang=en#troubleshooting)
- [Co2 Lasers](https://support.salasers.com/co2-lasers?hsLang=en#main-content)

    - [Razor Series](https://support.salasers.com/co2-lasers?hsLang=en#razor-series)
- [Troubleshooting](https://support.salasers.com/troubleshooting?hsLang=en)
- [EzCad 2](https://support.salasers.com/ezcad-2?hsLang=en)
- [How-To Guides](https://support.salasers.com/how-to-guides?hsLang=en)
- [Explainers](https://support.salasers.com/explainers?hsLang=en)
- [Tools & Features](https://support.salasers.com/tools-features?hsLang=en#main-content)

    - [User Interface](https://support.salasers.com/tools-features?hsLang=en#user-interface)
    - [Essential Functions](https://support.salasers.com/tools-features?hsLang=en#essential-functions)
    - [Layout and Design](https://support.salasers.com/tools-features?hsLang=en#layout-and-design)

# San Antonio Laser

SALasers.com Help Center

Copyright © 2026, San Antonio Laser